DEWALT DW744X 10-Inch Job Site Table Saw with 24-1/2-Inch Max Rip Capacity

DEWALT DW744X 10-Inch Job Site Table Saw with 24-1/2-Inch Max Rip Capacity For Sale Review

List Price:$960.00

Sell Price:Too low to display

Usually ships in 24 hours

DEWALT DW744X 10-Inch Job Site Table Saw with 24-1/2-Inch Max Rip Capacity Overview

Use the DEWALT DW744X table saw for professional cutting versatility on the jobsite or in your workshop. This portable table saw features an exclusive telescoping fence which delivers 24-1/2-inch rip capacity and speedy, smooth, and skillful adjustments. It’s crafted with a heavy duty, high-torque motor and an efficient dust collection port and includes an electronic feedback control and soft start for easier startup and cutting performance. Included with the DEWALT DW744X is: 10-inch, 24-tooth carbide blades; a folding table saw stand (DW7440); and a miter gauge.

I bought this saw primarily as a job site saw but it has seen some service in the workshop as well. It is ideally a two man lift not so much because of the weight but because it's awkward to man handle on your own, owing to the large table. I also purchased the additional outfeed and side supports which are great but they also add weight to the saw which have made it even heavier. As i work on my own the additional 30 inches of outfeed support has to be balanced against the extra weight.

The saw sits securely on the stand and has all the power anyone should need in a contractor saw. The rack and pinion fence is excellent and the best on the market in my opinion. I place the fence on the right hand side of the blade so the rip scale is set for me, anyone who sets the fence on the left will have to use their tape measure. The rip scale was out by a 1/16 of an inch and the fence was a 1/32 of an inch out of parallel with the blade. The mitre gauge seems as on all contractor saws to have been a bit of an after thought, there is a 1/16 of an inch of slop between the gauge bar and the gauge slots. This is not a huge issue for me as i rarely use it, when i do use the mitre gauge i push against the side of the mitre slot nearest the blade when making a cut.

There is onboard storage for spare blades and blade spanners, it's a pity Dewalt couldn't have included a cord wrap and onboard storage for the mitre gauge. There is an aluminum shield with a rubber extension which covers the bottom of the blade underneath the saw, this seemed to be holding the sawdust and overheating the motor. I removed it, it might be intended to be left in place if a shop-vac were attached to the dust port. I also removed the blade guard and the riving knife, these imo are workshop acessories.

The threaded bar that is attached to the handle that raises and lowers the blade is exposed, hence the threads get clogged with saw dust. Making it almost impossible to raise and lower the blade, i modified a piece of plastic tubing with a slightly larger diametre than the threaded bar by slitting it down the middle and slipping it over the bar. This has kept the saw dust off.

In conclusion i would'nt advise someone working jobsites on their own to buy this saw, it's just a bit too heavy and awkward. Ideally i'd leave the DW744 in the workshop and buy the DW745 which has the same size motor but with a reduced rip capacity and hence smaller table.

Just a little update on the above, the fence on my saw has a tendancy to drift towards the back of the blade which burns my stock as it clears the blade. This always seems to happen no matter how many times i re-adjust the fence. There are two 10mm bolts under the fence at the back of the table which need to be loosened to adjust the fence for parrallel. I recently went to re-adjust the fence and ended up tightening the bolts when i should have been loosening them, this sometimes happens when the bolt heads are facing down rather than up. I stripped out the threads in the bolt housings which unfortunatly are part of the cast table. I took the saw to the service centre and they gave me three options, thread locking compound, a new table, or a new saw. I choose the tread locking compound as a temporary fix, a new table will cost me 250 Euro. Expensive mistake.

Available At